Wednesday 6 August 2014

Completed: My First Homemade Bra

I've decided that this is the summer to conquer many of my sewing fears. Knits? Check. Bras? Check. Pants? Up next!



I've been curious about bra-making for a while now. It's always been really difficult to find bras that fit me well, since I have such a small ribcage.


I've been following Tasia and Caroline's posts about bra-making for a while, and finally, I decided that it was time to jump in and give it a go!




This is the Classic Bra from Pin-Up Girls, a basic and beginner-friendly bra pattern. I used a bra kit from Bra-Makers Supply, in beige. The kit comes with duoplex for the cups, bridge, and straps; power net for the back; and all the elastic, strapping, and other notions you need, except for wires. At $28, that's a pretty good deal for a bra, considering I usually pay $100 or more for one in my size!




I used the wire charts on Bra-Makers Supply's website to figure out what size wires to order. I printed out the chart and cut out along a couple different sizes, then held them up to see what size and shape seemed to fit. I ended up ordering a size 34, which fit perfectly!


I also ordered one of the books available from Bra-Makers Supply called Make & Fit Your Own Bra. I figured that it would be a useful resource for fitting problems and other patterns that don't have instructions as detailed as the Pin-Up Girls patterns. It was somewhat helpful, but I probably could have managed without. The order of construction in the book was a little different, but a lot of the instructions were exactly the same. The book does have more tips along the way and information on fitting, but I'm not entirely sure it was worth the extra $30. 


Once I had bought the pattern, the book, the kit, the wires, and some lace, it ended up not being cheaper than buying a bra - my total was about $130, including shipping, which was $15. However, I'll be able to use the pattern and the book again, and I have enough fabric left over for at least one more bra, if I buy the elastics and whatnot that I need. Now that I've bought the basics, it will be much cheaper to make more.


I found it a little funny that in both the pattern and the book, the method of choosing your size is the standard one where you measure your ribcage and your bust, which is apparently only accurate about half the time. (Come to think of it though, I've never heard of another way.) In my case, it's definitely not accurate. According to my measurements, I should be wearing a size 30B, when the bras I'm currently wearing are 28E, and they're a little too big in the band.


The smallest band size in this pattern is 30, so I cut a 30D and shortened the band by 2" to make it a 28E. I wasn't sure that this would be the right size, because my current bras are a little big in the cup, but I figured that it would be a good starting point.


I opted not to make any sort of muslin, and instead made the first bra expecting it not to be perfect, but a starting point. 


Cutting out this fabric is hard! It's super slippery, and the blade in my rotary cutter was pretty dull so I had a hard time cutting it. After cutting the first piece, I stopped cutting the pieces on the fold to stop them slipping around. It's the kind of fabric that I would usually avoid at all costs (100% polyester, slippery, and tough to sew through), but it does make a really nice bra.


It only took me an afternoon to put the bra together! I didn't have the right colour thread, so used an off-white for the seams and a slightly darker beige topstitching thread for the topstitching. It has a bit of a shine, which looks really nice, although it was a pain to keep switching thread all the time.

For the most part, I followed the instructions that came with the pattern, and used the tips from the book, but when it came to putting the wires in, I used the method in the book. The pattern says to leave the casing open at the underarm, insert them right at the end, and then close it with a bar tack, but the book says to leave it open at the centre. The method in the book encloses the edge of the wire casing in the elastic for a smoother finish, so I did that instead. I sewed the bar tack at the underarm through the outer fabric by accident, though, rather than just through the casing. Oops! It doesn't look too bad, though, and if I had followed the pattern instructions, there would have been a bar tack there anyways.


I'm not sure if this was because I strayed from the instructions or not, but I had trouble sewing the elastic at the centre where the wire casings are closed. I made this so long ago that I can't quite remember what happened, but I fixed it with some hand sewing. Next time, I might follow the pattern's instructions and see if I have the same problem.




I also found that the bottom bridge wasn't quite long enough, so the stitching was a little strained when I flipped the elastic to the wrong side. I think my stitching may have been not quite at the 1/4" seam allowance, but I might add a little next time anyways.



I used just over half of the strapping, since I find that straps are always too long on me. I really should have used lighter thread while sewing on the strap, but I don't feel like changing it.




Other than that, this went together really smoothly! I'm quite impressed with how professional it looks, aside from the rather dodgy stitching at the hook. I added the lace by zigzagging the edges on the cup pieces before I sewed the cups. Next time, I might add it after the cups have been sewn and cover a bit more of the cups with it, but that will be a little harder to sew. I wanted to keep it simple this time, but I love how the lace looks.






Enough about construction... does it fit?


Yes, but not perfectly. The usual fitting issue with me is that the cup is just a teeny bit too deep in the cup, but too low cut, making it look a little small. It's perfectly wearable though, and very comfortable! I'll try to fix the fitting issues in my next version, but this is a great starting point.


For my next version, I'll use the same fabric because I have lots left over, and I'll just order some more notions to match. I might try lining it in foam, because I'm not super fond of the fabric-only cups. I've never (except for once when I was 14) worn bras with lots of padding or push-up bras, but I like to have a little bit more coverage than just fabric. 




I think I'm hooked on bra-making, though. It's great to be able to make something so practical in an afternoon! I only wish that I could buy the supplies without ordering them online. I tried Dressew, but it was really hard to get all the notions to coordinate, and I don't know enough about bra-making (yet) to pick fabrics that will work.


What about you? Have you ever made a bra? Would you?

25 comments:

  1. really great work. i´m sewing on a bra to. But i need so much longer then you -.-

    ReplyDelete
    Replies
    1. Thank you! This was an unusual project for me because it was so quick. Usually I'm a super slow sewer! I'd rather take my time and have a nice finished product than rush though.

      Delete
  2. I've been starting to work on undergarments of my own, but since I'm rather poor with a high cup-to-band ratio I'm trying to draft my own pattern before actually sewing it up... we'll see how it goes! I'll probably test it out in plain cotton before buying 'real' bra fabrics. I like the lace addition on yours.

    ReplyDelete
    Replies
    1. Wow, that's awesome! I have no experience pattern drafting (aside from simple knit tops) so I wouldn't know where to start drafting my own pattern. Good luck with yours!

      Delete
    2. Thanks! I wouldn't have known where to start either, I used this tutorial, parts 1 and 2. http://www.foundationsrevealed.com/bra-making/161-bras-determining-your-size (I'm too cheap/poor to buy a membership to see the construction).
      I sewed one up, and it needs some changes but it's not too bad. The neck edge is too long, and in a woven the band is too short (It's probably supposed to be made in powermesh). And the deep dart leads to some unpleasant pokiness. :-/ But it's a start! And I didn't have to buy anything!

      Delete
    3. Thanks for the link! That'll be very useful if I decide to draft my own. Even if I don't, it looks like it might help me tweak the fit of this one. Thanks!

      Delete
  3. I haven't gone near bras yet, but have been in awe of Tasias! Yours looks incredibly professional. It's a lot harder to fit all the stuff in the UK but I am feeling inspired to have a go.

    ReplyDelete
    Replies
    1. Thanks! It's quite lucky that there's a Canadian store with all the supplies, since it's usually just as hard to find sewing supplies here.

      Delete
  4. That's awesome! And looks really well made... like you paid $100 at a store! I've not tried bra-making yet....

    ReplyDelete
    Replies
    1. Thank you! It really wasn't as hard as I thought it would be, so I would encourage anyone with some sewing experience to try it!

      Delete
  5. This was such a pleasure to read and it looks like you made an amazing bra, even if it doesn't fit you perfectly. I've only made a bralette before, which was nice, but I'm started to want to make one with underwires, but of course figuring out which size to get scares me a little. Thank you for linking to all of your resources!

    ReplyDelete
    Replies
    1. Thanks! I would say that if you can make a bralette, you can make a bra! It's just the fitting that's trickier. Good luck if you decide to give it a go!

      Delete
  6. Wow this just looks so professional. Good for you giving it a go.

    ReplyDelete
  7. Great job!!! Look also at http://www.madalynne.com it's a very nice sewing blog with lot about bra making...

    ReplyDelete
    Replies
    1. Thanks for the link - I hadn't seen that blog before.

      Delete
  8. I never really thought about bra-making before. It seems so complicated, but maybe someday I will give it a go. Try everything at least once, right? By the way, your bra came out very nice for your first try (and especially since you didn't make a muslin first). I'm glad it at least mostly fits. I'm sure you can fix your fitting problems in your next bra-making and then it will be perfect. :)

    Anyways, your blog has always been inspiring to me since we are both young seamstresses, so I've decided to nominate you for the Liebster blog award. You can see the post here: Liebster Blog Award Post

    ReplyDelete
    Replies
    1. It's not really that complicated if you just take it one step at a time. The techniques used really aren't anything new, you just need to use them in new ways.

      Thanks for the nomination! I've already been nominated for a few, and I'm afraid I still haven't gotten around to accepting them. One of these days, I will have to do a giant Liebster post!

      Delete
  9. Well done you! I have bought both my daughters kits to sew their own bras, but neither has yet actually done it- and neither have I. You are a great lass for having done this, and got such a professional result! I am off to look at the rest of what you have done- You are very impressive!

    ReplyDelete
  10. Wow : it does look professional!
    What a great job!!!
    I've been wanting to make my own bras for a while now... but I think I still don't feel brave enough ;)
    If I ever go for it, I'll definitely come back here to read all your helpful insights. Thanks!
    Well done, hope you're super proud of yourself!

    ReplyDelete
    Replies
    1. Thanks! It's really not as hard as it looks - I was surprised!

      Delete
  11. You can check out reddit's section called abrathatfits to demystify bra sizing. There are various blogs that do so as well, but odly enough that was the site that was clearest for me. Great job tackling suck a daunting garment!

    ReplyDelete
    Replies
    1. Thanks for the link! I'll be doing a lot more work on bramaking on my next break, and that looks like it will be quite helpful!

      Delete
  12. Great Keep it up,

    Shopperstrail offers wide collection of super soft bralette. You can find additional information on https://www.shopperstrail.com/

    ReplyDelete